Qsat tutorials

HINTS ON HOW TO UPGRADE YOUR QSAT
Inspite of the fact that i have personally tested this software on my qsat q11g, i also
scanned the file with Bit defender Antivirus total security 2014 and there is no virus of any
kind in this file, I am not to be held liable for any mistake or negligence on the part of
anybody using this software. This is because if you jettison my instructions and warnings,
you may soft-brick your qsat(soft bring translates to damaging the software part of your
device). However if you do all what is required of you, then you won’t have any problem
with the upgrade.
Warnings!!!: I will advice those who cannot setup their qsat from scratch not to upgrade
until they find those who can help them set it up. The reason being that after the upgrade,
your qsat will be reset to factory settings and as a result, three major things will happen
to your qsat immediatelly after the upgrade. 1.you xcam setup under settings will be
hidden (to bring this back because you need it to re-activate your avatarcam HD code dial
1512 once you open settings) 2. Your internet connection type will be reset to LAN
Internet (if you were not using lan internet previously then you need to choose your
preferred connection mode if you are using direct sim card otherwise known as 2g on your
remote press Menu>>Ethernet Config>>Under link type choose GPRS Network>>then Select
Config>>Under GPRS Network Window>Area>>Select your country>>Operator>>select your
provide>>>Mark auto link and reboot your decoder) 3. Your channels will all vanish (to
rescan your channels, goto installation>>password is 0000>>Antenna Setting>>Change
Satellite to Eutelsat 36A, 36/ 036.0E>>press blue button on your remoe to start
scanning>>another window will pop up change scan type from manual to Blind
scan>>press enter and wait till everything completes.) 4. Your avatarcam code will be
deactivated you need to re-activate it after the firmware upgrade (to do this press
menu>>setting>>xcam setup>>AvatarCamHD>>press red button>>press green
button>>reboot your qsat) If your avatarcamhd code begins with 54xx or 56xxx, for now
your channels may take longer to come up, to hasting this, try the following tricks; use a
3g modem with mtn Nigeria, etisalat or glo>> now goto multimedia>>iptv>>open any of
the iptv channels and watch for seconds>>go back to your dst* channels>>it should be
showing by now.
You must have a stable electricity, if your electricity is not stable, please use an
inverter or a generator.
You must use only a virus free USB flashdrive( to be sure of this, you can format the
usb drive before you copy the file into it)
Once you download my files, you will need to extract it after extraction, you will see
two files inside the folder, the read me file .txt and the software .bin you are required
to copy only the .bin file to your flashdrive then read the text file.
It is worthy of note that your qsat need not be connected to the internet throughout
the upgrading process.
Download the latest Version 6 software of qsat from the following article: Download
Qsat Software V6 For Q11G, Q13G & Q15G [Fixes Code 54xxx & Code 56 Issues for
Now]
Download For QIIG: Q11G-_V5.11.20_20131221_3.zip ( No password required to
extract) or FOR Q13G: Q13G-_V5.11.20_20131221.zip ( No password required to
extract)and for Q15G: Q15G-_V5.11.23_20131224 ( You need to extract the Q15G
software with a password and the password is <lemmymorgan.com> )
Once you have met the above requirements, please plugin your usb to your qsat, on
your remote now press MENU>>UPGRADE>>USB / UPGRADE, select the file you
copied to your usb earlier and click on ok to start the process. Once the process is
completed, your decoder will reboot that is all.